HomeMy WebLinkAboutPAINTING_Rev_0Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 1 of 6
SECTION 09 90 00
PAINTING
PART 1 GENERAL
1.01 SUMMARY
A. This Section includes surface preparation and field painting of exposed exterior and interior items and
surfaces. Paint surfaces indicated on the Drawings, in schedules, and as described below.
1. Colors: Color schedule will be supplied to Contractor during "Submittals" review. Allow for up to 8
colors including 4 custom matches.
2. Painting includes, but is not necessarily limited to, the following surfaces in the areas indicated for
work of this Contract. Also refer to the Drawings and Schedules.
a. 057000 Metal Fabrications Interior - where exposed.
b. 081113 Hollow Mtl. Doors and Frames All.
c. 092116 Gypsum Board Assemblies All exposed, new and existing, except
where scheduled for epoxy.
d. Divisions 21-28 Mechanical & Electrical Paint new and existing exposed ducts,
conduit, boxes, panels, and pipe located on walls or ceilings scheduled for paint. Painting
includes field painting of exposed bare and covered pipes and ducts, hangers, exposed steel
and iron supports, and surfaces of mechanical and electrical equipment that do not have a
factory-applied final finish.
3. Paint exposed surfaces, except where these Specifications indicate that the surface or material is
not to be painted or is to remain natural. If an item or a surface is not specifically mentioned, paint
the item or surface the same as similar adjacent materials or surfaces. If a color or finish is not
indicated, Architect will select from standard colors and finishes available.
B. Do not paint prefinished items, concealed surfaces, finished metal surfaces, operating parts, and labels.
1. Labels: Do not paint over UL, FMG, or other code-required labels or equipment name,
identification, performance rating, or nomenclature plates.
2. Do not paint electrical cables or wiring.
1.02 SUBMITTALS
A. Product Data: For each paint product indicated, including block fillers and primers.
1. Material List: An inclusive list of required coating materials. Indicate each material and
cross-reference specific coating, finish system, and application. Identify each material by
manufacturer's catalog number and general classification.
2. Manufacturer's Information: Manufacturer's technical information, including label analysis and
instructions for handling, storing, and applying each coating material. MSDS sheets are not
required.
B. Samples for Initial Selection: Color chip set including manufacturer’s full range of colors for each type of
finish-coat material indicated. Architect will select from chips or provide samples for custom match.
C. Samples for Verification: For each color to be applied, whether selected from manufacturer’s standards
or custom-mixed to match Architect’s sample, provide samples of the actual products on the substrates
listed below.
1. Resubmit until required sheen, color, and texture are achieved.
2. Label each Sample with material, color, location and application.
3. Submit 2 Samples on the following substrates for Architect's review of color and texture only:
a. Smooth surfaces such as troweled concrete, metal, painted wood, gypsum board and plaster
provide sample on manufacturer’s drawdown cards.
b. Stained or Natural Wood: See 06 41 00 - Architectural Wood Casework.
1.03 QUALITY ASSURANCE
A. Applicator Qualifications: A firm or individual experienced in applying paints and coatings similar in
material, design, and extent to those indicated for this Project, whose work has resulted in applications
with a record of successful in-service performance.
B. Source Limitations: Obtain block fillers and primers for each coating system from the same manufacturer
as the finish coats.
1.04 DELIVERY, STORAGE, AND HANDLING
A. Deliver materials to Project site in manufacturer's original, unopened packages and containers bearing
manufacturer's name and label, generic classification or binder type, and color name and number.
Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 2 of 6
B. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient
temperature of 45 deg F. Maintain storage containers in a clean condition, free of foreign materials and
residue. Protect from freezing. Keep storage area neat and orderly. Remove oily rags and waste daily.
1.05 PROJECT CONDITIONS
A. Apply paints only when temperatures of surfaces to be painted and surrounding air comply with
manufacturer’s instructions.
B. Do not apply paint in snow, rain, fog, or mist; or when relative humidity exceeds 85 percent; or at
temperatures less than 5 deg F above the dew point; or to damp or wet surfaces.
1. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed
and heated within temperature limits specified by manufacturer during application and drying
periods.
1.06 EXTRA MATERIALS
A. Furnish extra paint materials of the identical type and color as the materials applied and in the quantities
described below. Identify with labels describing contents and location(s) used. Deliver extra materials to
Owner.
1. Quantity: Furnish Owner with 1 gal. extra of each paint and/or coating used on Project.
PART 2 PRODUCTS
2.01 MANUFACTURERS
A. Manufacturers: Subject to compliance with requirements and verification of substrate compatibility,
provide the painting systems listed from the following manufacturers. For other manufacturers, comply
with substitution requirements in Division 1.
1. Benjamin Moore.
2. Diamond Vogel.
3. PPG Paints. (Pittsburgh Paints).
4. Sherwin-Williams Co.
2.02 PAINT MATERIALS, GENERAL
A. Refer to the Schedule at the end of this Section for painting system descriptions, including primer types
and number of finish coats. Acceptable products to use for these systems are listed below. If a surface is
indicated to be painted but is not listed below, provide a finish system recommended by the paint
manufacturer for that surface that is of equivalent quality to the listed products.
B. Material Compatibility: Provide block fillers, primers, and finish-coat materials that are compatible with
one another and with the substrates indicated under conditions of service and application, as
demonstrated by manufacturer based on testing and field experience.
C. Material Quality: Provide manufacturer's best-quality paint material of the various coating types specified
that are factory formulated and recommended by manufacturer for application indicated. Paint-material
containers not displaying manufacturer's product identification will not be acceptable.
D. Colors: As selected by Architect from manufacturer's full range. Provide custom matches to samples
provided by the Architect where indicated.
2.03 EXTERIOR PRIMERS
A. Exterior Ferrous-Metal Primer: Factory-formulated rust-inhibitive metal primer for exterior application.
Applied to result in a dry film thickness of not less than 2.0 mils.
1. Benjamin Moore; Super Spec Alkyd Metal Primer P06
2. Diamond Vogel: CoteAll Multi-Purpose Alkyd Primer.
3. PPG Paints; 6-208 SpeedHide Interior/Exterior Rust Inhibiting Primer.
4. Sherwin-Williams; Kem Kromik Universal Metal Primer B50NZ6/B50WZ1.
B. Exterior Galvanized Metal Primer: Factory-formulated galvanized metal primer for exterior application.
Applied to result in a dry film thickness of not less than 2.0 mils.
1. Benjamin Moore; Super Spec Acrylic Metal Primer P04
2. Diamond Vogel: Vers-Acryl 300 Acrylic Maintenance Primer/Finish.
3. PPG Paints; 6-209 SpeedHide Interior/Exterior Galvanized Steel Primer.
4. Sherwin-Williams; Galvite HS Paint B50WZ30.
2.04 INTERIOR PRIMERS
A. Interior Zero-VOC Gypsum Board Primer (M.P.I. #149): Factory-formulated latex-based primer for interior
application. Applied to result in a dry film thickness of not less than 1.5 mils.
1. Benjamin Moore; Eco Spec WB Primer N372
Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 3 of 6
2. Diamond Vogel: Health-Kote Primer Interior Zero VOC Latex Primer.
3. PPG Paints; Speedhide Zero Latex Primer/Sealer. 6-4900XI
4. Sherwin Williams; Harmony Latex Primer B11W01500
B. Interior Ferrous-Metal Primer (MPI #79): Factory-formulated quick-drying rust-inhibitive alkyd-based
metal primer. Applied to result in a dry film thickness of not less than 2.0 mils.
1. Benjamin Moore; Super Spec Alkyd Metal Primer P06
2. Diamond Vogel: Iron Prime 600 Fast Dry Universal Primer.
3. PPG Paints; Speedhide Rust Inhibitive Steel Primer 6-212.
4. Sherwin-Williams; Kem Kromik Universal Metal Primer B50AZ6/B50NZ6/B50WZ1.
2.05 EXTERIOR FINISH COATS
A. Exterior Semi-Gloss Alkyd Enamel (MPI #81): Factory-formulated full-gloss alkyd enamel for exterior
application. Applied to result in a dry film thickness of not less than 2.0 mil per coat.
1. Benjamin Moore; Super Spec HP “D.T.M. Alkyd Semi-Gloss P24.
2. Diamond Vogel: CoteAll Multi-Purpose Alkyd Semi Gloss
3. PPG Paints; Dev-Guard Semi-Gloss Enamel. 4306.
4. Sherwin-Williams; Industrial Enamel B-54 Series.
2.06 INTERIOR FINISH COATS
A. Interior Semigloss Low-odor Zero-VOC Acrylic Enamel (MPI #147): Factory-formulated semigloss
acrylic-latex enamel for interior application. Applied to result in a dry film thickness of not less than 1.5
mils per coat.
1. Benjamin Moore; Natura 0 VOC Interior Latex Semi-Gloss Finish #514.
2. Diamond Vogel: Zero Plus Interior Zero VOC Latex Semi-Gloss Enamel.
3. PPG Paints; SpeedHide Zero Interior Semi-Gloss Enamel. 6-4510XI.
4. Sherwin Williams; B10 Harmony Latex Semi-Gloss.
B. Interior Semigloss Alkyd Enamel (MPI #47): Factory-formulated semigloss alkyd enamel for interior
application. Applied to result in result in a dry film thickness of not less than 1.7 mils per coat.
1. Benjamin Moore; Super Spec Alkyd Semi-Gloss Enamel No. 271:
2. Diamond Vogel: Satinamel Interior/Exterior Alkyd Enamel.
3. PPG Paints; 6-1110XI Series SpeedHide Interior Enamel Wall & Trim Semi-Gloss Oil 6-1110.
4. Sherwin-Williams; ProMar 200 Interior Alkyd Semi-Gloss Enamel B34W200 Series.
C. Interior Epoxy Topcoats: Semi-gloss, low-odor, waterborne epoxy applied in a minimum of two coats at
spreading rate recommended by manufacturer to achieve a total dry film thickness of 4.0 to 6.0 mils.
1. Benjamin Moore Corotech Pre-Catalyzed Waterborne Epoxy Semi-Gloss V341
2. Carboline: Sanitile 555 Waterborne epoxy.
3. Diamond Vogel: Vers-E-Poxy 131 Waterborne Acrylic Epoxy.
4. PPG Paints: Pitt-Glaze WB 16-551.
5. S-W: Pro Industrial Water Based Catalyzed Epoxy, B73 Series.
PART 3 EXECUTION
3.01 EXAMINATION
A. Examine substrates, areas, and conditions, with Applicator present, for compliance with requirements for
paint application. Comply with procedures specified in PDCA P4.
1. Proceed with paint application only after unsatisfactory conditions have been corrected and
surfaces receiving paint are thoroughly dry.
2. Start of painting will be construed as Applicator's acceptance of surfaces and conditions within a
particular area.
B. Coordination of Work: Review other Sections in which primers are provided to ensure compatibility of the
total system for various substrates. On request, furnish information on characteristics of finish materials
to ensure use of compatible primers.
1. Notify Architect about anticipated problems when using the materials specified over substrates
primed by others.
3.02 PREPARATION
A. General: Remove hardware and hardware accessories, plates, machined surfaces, lighting fixtures, and
similar items already installed that are not to be painted. If removal is impractical or impossible because
of size or weight of the item, provide surface-applied protection before surface preparation and painting.
1. After completing painting operations in each space or area, reinstall items removed using workers
skilled in the trades involved.
Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 4 of 6
B. Protection: Provide and maintain masking, tarpaulins, and other protections as required to prevent
overspray, splatter or drips on adjacent surfaces.
C. Cleaning: Before applying paint or other surface treatments, clean substrates of substances that could
impair bond of the various coatings. Remove oil and grease before cleaning.
1. Schedule cleaning and painting so dust and other contaminants from the cleaning process will not
fall on wet, newly painted surfaces.
D. Surface Preparation: Clean and prepare surfaces to be painted according to manufacturer's written
instructions for each particular substrate condition and as specified.
1. Test existing paints for lead and perform removal of lead-containing paints according to appropriate
local, state and federal rules and laws.
2. Provide barrier coats over incompatible primers or remove and reprime.
3. Cementitious Materials: Prepare concrete, concrete unit masonry, cement plaster, and
mineral-fiber-reinforced cement panel surfaces to be painted by removing efflorescence, chalk,
dust, dirt, grease, oils, and release agents. Roughen as required to remove glaze. If hardeners or
sealers have been used to improve curing, use mechanical methods of surface preparation.
a. Use abrasive blast-cleaning methods if recommended by paint manufacturer.
b. Determine alkalinity and moisture content of surfaces by performing appropriate tests. If
surfaces are sufficiently alkaline to cause the finish paint to blister and burn, correct this
condition before application. Do not paint surfaces if moisture content exceeds that permitted
in manufacturer's written instructions.
c. Clean concrete floors to be painted with a 5 percent solution of muriatic acid or other etching
cleaner. Flush the floor with clean water to remove acid, neutralize with ammonia, rinse, allow
to dry, and vacuum before painting.
4. Ferrous Metals: Clean ungalvanized ferrous-metal surfaces that have not been shop coated;
remove oil, grease, dirt, loose mill scale, and other foreign substances. Use solvent or mechanical
cleaning methods that comply with SSPC's recommendations.
a. Touch up bare areas and shop-applied prime coats that have been damaged. Wire-brush,
clean with solvents recommended by paint manufacturer, and touch up with same primer as
the shop coat.
5. Galvanized Surfaces: Clean galvanized surfaces with nonpetroleum-based solvents so surface is
free of oil and surface contaminants. Remove pretreatment from galvanized sheet metal fabricated
from coil stock by mechanical methods.
E. Material Preparation: Mix and prepare paint materials according to manufacturer's written instructions.
1. Stir material before application to produce a mixture of uniform density. Stir as required during
application. Do not stir surface film into material. If necessary, remove surface film and strain
material before using.
2. Use only thinners approved by paint manufacturer and only within recommended limits.
3.03 APPLICATION
A. General: Apply paint according to manufacturer's written instructions. Use applicators and techniques
best suited for substrate and type of material being applied.
1. Do not paint over dirt, rust, scale, grease, moisture, scuffed surfaces, or conditions detrimental to
formation of a durable paint film.
2. The term "exposed surfaces" includes areas visible when permanent or built-in fixtures, grilles,
convector covers, covers for finned-tube radiation, and similar components are in place. Extend
coatings in these areas, as required, to maintain system integrity and provide desired protection.
3. Paint surfaces behind movable equipment and furniture the same as similar exposed surfaces.
Before final installation of equipment, paint surfaces behind permanently fixed equipment or
furniture with prime coat only.
4. Paint interior surfaces of ducts with a flat, nonspecular black paint where visible through registers or
grilles.
5. Paint backsides of access panels and removable or hinged covers to match exposed surfaces.
6. Finish doors on tops, bottoms, and side edges the same as exterior faces.
7. Finish interior of wall and base cabinets and similar field-finished casework to match exterior.
8. Sand lightly between each succeeding enamel or varnish coat.
B. Scheduling Painting: Apply first coat to surfaces that have been cleaned, pretreated, or otherwise
prepared for painting as soon as practicable after preparation and before subsequent surface
deterioration.
Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 5 of 6
1. The number of coats and film thickness required are the same regardless of application method. If
sanding is required to produce a smooth, even surface according to manufacturer's written
instructions, sand between applications.
2. Omit primer over metal surfaces that have been shop primed and touchup painted.
3. If undercoats, stains, or other conditions show through final coat of paint, apply additional coats
until paint film is of uniform finish, color, and appearance. Give special attention to ensure that
edges, corners, crevices, welds, and exposed fasteners receive a dry film thickness equivalent to
that of flat surfaces.
4. Allow sufficient time between successive coats to permit proper drying. Do not recoat surfaces until
paint has dried to where it feels firm, and does not deform or feel sticky under moderate thumb
pressure, and until application of another coat of paint does not cause undercoat to lift or lose
adhesion.
C. Application Procedures: Apply paints and coatings by brush, roller, spray, or other applicators according
to manufacturer's written instructions.
1. Brushes: Use brushes best suited for type of material applied. Use brush of appropriate size for
surface or item being painted.
2. Rollers: Use rollers of carpet, velvet-back, or high-pile sheep's wool as recommended by
manufacturer for material and texture required.
3. Spray Equipment: Use airless spray equipment with orifice size as recommended by manufacturer
for material and texture required.
D. Minimum Coating Thickness: Apply paint materials to thickness specified but no thinner than
manufacturer's recommended spreading rate to achieve dry film thickness indicated. Provide total dry
film thickness of the entire system to thickness specified but no thinner than as recommended by
manufacturer.
E. Prime Coats: Before applying finish coats, apply a prime coat, as recommended by manufacturer, to
material that is required to be painted or finished and that has not been prime coated by others. Recoat
primed and sealed surfaces where evidence of suction spots or unsealed areas in first coat appears, to
ensure a finish coat with no burn-through or other defects due to insufficient sealing.
F. Pigmented (Opaque) Finishes: Completely cover surfaces as necessary to provide a smooth, opaque
surface of uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush
marks, runs, sags, ropiness, or other surface imperfections will not be acceptable.
G. Transparent (Clear) Finishes: Use multiple coats to produce a glass-smooth surface film of even luster.
Provide a finish free of laps, runs, cloudiness, color irregularity, brush marks, orange peel, nail holes, or
other surface imperfections.
H. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or repaint
work not complying with requirements.
3.04 CLEANING
A. Cleanup: At the end of each workday, remove empty cans, rags, rubbish, and other discarded paint
materials from Project site.
1. After completing painting, clean glass and paint-spattered surfaces. Remove spattered paint by
washing and scraping without scratching or damaging adjacent finished surfaces.
3.05 PROTECTION
A. Protect work of other trades, whether being painted or not, against damage from painting. Correct
damage by cleaning, repairing or replacing, and repainting, as approved by Architect.
B. Provide "Wet Paint" signs to protect newly painted finishes. After completing painting operations, remove
temporary protective wrappings provided by others to protect their work.
1. After work of other trades is complete, touch up and restore damaged or defaced painted surfaces.
3.06 EXTERIOR PAINT SCHEDULE
A. Provide the following finish systems over the substrates indicated. Refer to Part 2 of this Section for
acceptable products for each system. If a surface is indicated to be painted but is not listed below,
provide a finish system recommended by the paint manufacturer that is of equivalent quality to the listed
products.
B. Ferrous Metal: Provide the following finish systems over exterior ferrous metal. Primer is not required on
shop-primed items except for touch-up.
1. Gloss Alkyd-Enamel Finish: Two finish coats over a rust-inhibitive primer.
a. Primer: Exterior ferrous-metal primer.
b. Finish Coats: Exterior gloss alkyd enamel.
Five Sullivan Brothers CC Kitchen Plmb Improvements 09 90 00
City of Waterloo PAINTING
INVISION #16021 6 of 6
C. Zinc-Coated Metal: Provide the following finish systems over exterior zinc-coated metal surfaces:
1. Gloss Alkyd-Enamel Finish: Two finish coats over a galvanized metal primer.
a. Primer: Exterior galvanized metal primer.
b. Finish Coats: Exterior gloss alkyd enamel.
3.07 INTERIOR PAINT SCHEDULE
A. Provide the following finish systems over the substrates indicated. Refer to Part 2 of this Section for
acceptable products for each system. If a surface is indicated to be painted but is not listed below,
provide a finish system recommended by the paint manufacturer that is of equivalent quality to the listed
products.
B. Gypsum Board (Typical): Provide the following finish systems over interior gypsum board surfaces:
1. Low-Luster Acrylic-Enamel Finish: Two finish coats over a primer.
a. Primer: Interior gypsum board primer.
b. Finish Coats: Interior low-luster acrylic enamel.
C. Gypsum Board (Toilets): Provide the following finish systems over interior gypsum board surfaces in
damp areas:
1. Water-based Epoxy Finish: Two finish coats over a primer.
a. Primer: Interior gypsum board primer.
b. Finish Coats: Water-based Epoxy.
D. Ferrous Metal: Provide the following finish system over ferrous metal:
1. Semigloss Alkyd-Enamel Finish: Two finish coats over a primer.
a. Primer: Interior alkyd ferrous-metal primer.
b. Finish Coats: Interior semigloss alkyd enamel.
2. Semigloss Acrylic-Enamel Finish: Two finish coats over a primer.
a. Primer: Interior water-based ferrous-metal primer.
b. Finish Coats: Interior semigloss acrylic enamel.
E. Overhead structure and deck, ductwork, piping, and conduit: Provide the following finish system over
overhead surfaces:
1. Low-Luster or Flat Acrylic-latex Finish: Single primer/finish coat.
a. Primer/Finish Coats: Interior low-luster or flat acrylic dry-fall coating. (Provide separate primer
if required for incompatible surfaces, as determined by pre-installation testing).
END OF SECTION