HomeMy WebLinkAboutDOMESTIC PLUMBING SPECIALTIES_Rev_0Five Sullivan Brothers CC Kitchen Plmb Improvements 22 11 19City of Waterloo DOMESTIC PLUMBING SPECIALTIES
INVISION #16021 1 of 2
SECTION 22 11 19
DOMESTIC PLUMBING SPECIALTIES
PART 1 GENERAL
1.01 SECTION INCLUDES
A. Clean out
B. Grease interceptor
1.02 RELATED SECTIONS
A. Specification Section 22 11 16 - Domestic Plumbing Piping
B. Specification Section 22 30 00 - Plumbing Equipment
C. Specification Section 22 40 00 - Plumbing Fixtures
1.03 REFERENCES
A. ASME A113.6.3; Floor and Trench Drains
B. PDI G-101 - Testing and Rating Procedure for Grease Interceptors with Appendix of Sizing andInstallation Data.
C. NSF/ANSI 61 - Drinking Water System Components - Health Effects.
D. NSF/ANSI 372 - Drinking Water System Components - Lead Content.
1.04 SUBMITTALS
A. Product Data: Provide component sizes, rough-in requirements, service sizes and finishes.
B. Shop Drawings: Indicate dimensions, weights and placement of openings and holes.
C. Certificates: Certify that grease interceptors meet or exceed specified requirements.
D. Manufacturer's Instructions: Indicate assembly and support requirements.
E. Project Record Documents: Record actual locations of equipment, clean out, backflow
preventers, water hammer arrestors.
F. Operation Data: Indicate frequency of treatment required for interceptors.
G. Maintenance Data: Include installation instructions, spare parts lists, exploded assembly views.
1.05 QUALITY ASSURANCE
A. Manufacturer Qualifications: Company specializing in manufacturing the products specified inthis section with minimum three years experience.
1.06 DELIVERY, STORAGE AND PROTECTION
A. Accept specialties on site in original factory packaging. Inspect for damage.
1.07 REGULATORY REQUIREMENTS
A. Wetted surfaces of brass and bronze components shall contain <0.25% weighted average leadcontent (lead free) as defined by NSF/ANSI Standards 61 and 372.
PART 2 PRODUCTS
2.01 CLEAN OUT
A. Manufacturers:
1. Watts
2. Smith
3. Josam
4. Wade
5. Sun Drainage6. Engineer approved equal.
B. Interior Finished Sub or On Grade Floors:
1. Watts #C0-200-R
Five Sullivan Brothers CC Kitchen Plmb Improvements 22 11 19City of Waterloo DOMESTIC PLUMBING SPECIALTIES
INVISION #16021 2 of 2
2. Lacquered cast iron bodies with integral anchor flange, neoprene "O" ring secondary test
seal and adjustable combined access cover and plug with gasket seal. Nickel-bronzescoriated cover in service area and round with depressed cover to accept floor finish infinished floor areas.
C. Interior Finished Membrane Floor Areas:
1. Watts #CO-200-C-R
2. Lacquered cast iron, two piece body with double drainage flange, weep holes, reversibleclamping collar and adjustable nickel-bronze strainer round with scoriated cover in serviceareas and round with depressed cover to accept floor finish in finished floor areas.
D. Interior Finished Wall Areas:
1. Watts #CO-380-RD2. Line type with lacquered cast iron body and round epoxy coated gasket cover and roundstainless steel access cover secured with machine screw.
E. Cleanout size shall be equal to pipe size up to 4 inches.
2.02 GREASE INTERCEPTOR (GI-1)
A. Manufacturers:
1. MiFab2. Schier
3. Green Turtle
4. Engineer approved equal.
B. Construction:
1. Material: HDPE2. Rough-in: Below grade.
3. Accessories: See detail on drawings.
4. Cover: Traffic rated. See detail on drawings.
C. Unit size and routing must be approved by authority having jurisdiction (Water ReclamationAuthority in particular areas) prior to rough-in.
PART 3 EXECUTION
3.01 PREPARATION
A. Coordinate cutting and forming of roof and floor construction to receive drains to require invertelevations.
3.02 INSTALLATION
A. Install in accordance with manufacturer's instructions.
B. Extend clean out to finished floor or wall surface. Lubricate threaded clean out plugs withmixture of graphite and linseed oil. Ensure clearance at clean out for rodding of drainagesystem. Coordinate all cleanout locations with the architect.
C. Furnish and install cleanouts at locations as specified and required by local plumbing code.
D. Install floor clean out at elevation to accommodate finished floor.
E. Install approved potable water protection devices on plumbing lines where contamination ofdomestic water may occur; on boiler feed water lines, janitor rooms, fire sprinkler systems,premise isolation, irrigation systems, flush valves, interior hose bibbs and exterior wall hydrants.
F. Install air gap fittings at all equipment drains when equipment is connected to domestic water.
G. Coordinate all wall mounted device locations with architect.
H. Route grease interceptor vent pipes back through building to roof. Coordinate routing withengineer and architect prior to rough-in.
END OF SECTION