Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
5 Sullivan Bros Kitchen Remodel-Warranty, Operation & Maintenance Manual
5 Sullivan Brothers Convention Center Kitchen Remodel Operations, Maintenance and Warranty Manual 208 East State Street Mason City, Iowa 50401 641-423-5674 Fax 641-423-9244 5 Sullivan Brothers Convention Center Kitchen Remodel OPERATIONS, MAINTENANCE & WARRANTY MANUAL TABLE OF CONTENTS Henkel Warranty Letter Contact List Specification Description Item 05 5000 - METAL FABRICATIONS ...........................................Dock Angle Shop Drawings 07 9200 - JOINT SEALANTS .....................................................Warranty Product Information 09 6700 - FLUID-APPLIED FLOORING .....................................Workmanship Warranty Maintenance Information Product Information 22 0050 - BASIC PLUMBING REQUIREMENTS ........................General Plumbing Warranty 22 1116 - DOMESTIC PLUMBING PIPING ...............................PEX Warranty PEX Product Information 22 4000 - PLUMBING FIXTURES .............................................Product Information 208 East State Street Mason City, Iowa 50401 641-423-5674 Fax 641-423-9244 HENKEL CONSTRUCTION COMPANY WARRANTY PROJECT: 5 Sullivan Brothers Convention Center Kitchen Remodel SUBSTANTIAL COMPLETION DATE: February 3, 2020 Henkel Construction Company guarantees all workmanship and installation provided by our company for a period of one year from the date of Substantial Completion. Please feel free to contact us with any questions or concerns. It has been our pleasure to work with you. __________________________________________ Gary J. Schmit, President HENKEL CONSTRUCTION COMPANY 5 Sullivan Brothers Convention Center Kitchen Remodel Contact List Contractor Responsible For: Henkel Construction Company ............................. General Construction Contact: Brian Tenge 208 East State Street Mason City, IA 50401 Phone: 641-423-5674 Fax: 641-423-9244 Bergen PHC .............................................................Plumbing Contact: Eric Frost 35 Fletcher Ave. Waterloo, Iowa 50701 Phone: (319) 234-1404 Community Electric, Inc. .........................................Electrical Contact: Mike Palmer 1510 Falls Ave Waterloo, Iowa 50701 Phone: 319-234-2580 Starting Line Flr Coatings Inc ...................................Fluid-Applied Flooring Contact: Kelly DeMorett 14607 Felton Court #112 Apple Valley, Minnesota 55124 Phone: 952-882-9498 05 5000 - METAL FABRICATIONS Dock Angle Shop Drawings Letter of Transmittal THE IRON WORKS, LTD. Date: 12-09-19 1924 SW 2nd Street Des Moines, IA 50315 Job No. 19-1602 (515)288-8981 Fax (515)288-3257 5-Sullivian Brothers Conv. Cntr. To: Henkel Construction Company Attention: Dylan Belvo Subject: 5-Sullivan Brothers Convention Center Kitchen Renovation WE ARE SENDING YOU: x Attached Under separate cover via the following items: x Shop drawings Prints Plans Samples Specifications Copy of letter Change order Other Document Type Copies Date No. Description Drawing Files 1-E 12-09-19 Drawing 1 THESE ARE TRANSMITTED as checked below: x For approval Approved as submitted Resubmit ____ copies for approval For your use Approved as noted Submit ____ copies for distribution As requested Returned for corrections x Return __1_ corrected prints For review and comment For your signature and return FOR BIDS DUE PRINTS RETURNED AFTER LOAN TO US REMARKS THANKS COPY TO SIGNED: Mike Chafa 07 9200 - JOINT SEALANTS Warranty 208 East State Street Mason City, Iowa 50401 641-423-5674 Fax 641-423-9244 HENKEL CONSTRUCTION COMPANY WARRANTY PROJECT: 5 Sullivan Brothers Convention Center Kitchen Plumbing Improvements Waterloo, Iowa SUBSTANTIAL COMPLETION DATE: February 3, 2020 Henkel Construction Company guarantees all workmanship and installation provided by our company in relation to the silicone sealants installed per Specification Section 079200 Joint Sealants for a period of twenty years from the date of Substantial Completion. Please feel free to contact us with any questions or concerns. It has been our pleasure to work with you. __________________________________________ Gary J. Schmit, President HENKEL CONSTRUCTION COMPANY 07 9200 - JOINT SEALANTS Product Information DAP® 100% Silicone Rubber Window, Door & Siding Sealant DAP® 100% SILICONE RUBBER WINDOW, DOOR & SIDING SEALANT is a durable, 100% waterproof and weatherproof sealant for sealing out drafts, water and moisture around windows, doors, siding, gutters, flashing, pipes, vents and more. It stays flexible to withstand expansion and contraction without cracking or losing adhesion. Cured sealant is mold and mildew resistant. Interior/exterior use. When tested in accordance with ASTM C719 meets the ASTM C920 requirements for Class 25, Use G 100% waterproof & weatherproof seal Flexible Cured sealant is mold & mildew resistant Interior/exterior use PACKAGING COLOR UPC 2.8 fl oz (82.8 mL) White 7079800752 2.8 fl oz (82.8 mL) Clear 7079800753 9.8 fl oz (289 mL) White 7079808646 9.8 fl oz (289 mL) Clear 7079808641 9.8 fl oz (289 mL) Almond 7079808649 9.8 fl oz (289 mL) Aluminum 7079808643 9.8 fl oz (289 mL) Bronze 7079808647 9.8 fl oz (289 mL) Black 7079808642 PRODUCT DESCRIPTION KEY FEATURES & BENEFITS USE FOR CAULKING & SEALING: Windows Doors Siding Trim Pipes Vents Ducts Gutters Flashing ADHERES TO: Wood Composite wood Aluminum Most metals* Glass Ceramic Porcelain Vinyl Most plastics & rubbers Most rubbers Apply when surface temperatures are between -35°F to 140°F. Joint width should not exceed ½”. If joint depth exceeds ½”, use foam backer rod. Allow 24 hours for sealant to fully cure. Sealant will not cure in totally confined spaces. Not recommended for continuous underwater use, filling butt joints, surface defects, tuck-pointing, chimneys, stovepipes or fireplace applications. Not recommended for structural glazing. Corrodes some metals. *Not recommended for use on or near brass, copper or copper alloys, zinc, iron, galvanized metals or other surfaces prone to attack by weak acids. Not for oily woods or cementitious surfaces. Substrates made of methylmethacrylate, polycarbonate, polypropylene, polyethylene and polytetrafluroethylene do not allow for best adhesion and compatibility with sealant. Try test area before using. Not paintable. Paint substrate surface before applying sealant. Store below 80°F in dry place for optimal shelf life. Surface Preparation Surface must be clean, dry, structurally sound and free of old caulk, dirt, dust & other foreign material. Product Application 1. If using squeeze tube, remove cap & cut nozzle at 45º angle to desired bead size. Unscrew nozzle & remove foil seal. Replace nozzle. 2. Is using cartridge, cut nozzle at a 45° angle to desired bead size. Puncture inner foil seal. Load into caulk gun. 3. Fill gap or crack with sealant. 4. If necessary, tool or smooth the bead of sealant with a finishing tool before the sealant skins over. 5. Allow sealant to cure for at least 12 hours before exposing to water. SUGGESTED USES FOR BEST RESULTS APPLICATION 3/3/2019 6. Do not touch or clean sealant for 24 hours. Sealant reaches full cure in 24 hours. 7. Clean up excess uncured sealant from surface and tools with mineral spirits. Scrape or cut away excess cured sealant. Do not use mineral spirits to clean hands or skin. Wash hands or skin with soap and water. 8. Sealant is not paintable. Paint surfaces prior to applying sealant. 9. Reseal cartridge/tube for storage and reuse. Typical Uncured Physical Properties Appearance/Consistency Smooth, gunnable paste Base Polymer Silicone rubber Filler Not applicable Volatile Not applicable Weight % Solids >97% Density (lbs per gallon) 8.0 Odor Vinegar like Clean Up Mineral spirits Flash Point >212ºF Freeze Thaw Stability (ASTM C1183) Will not freeze Shelf Life 24 months Coverage 9.8 oz: 53 linear feet at 3/16” diameter bead 2.8 oz: 15 linear feet at 3/16” diameter bead Typical Application Properties Application Temperature Range -35ºF to 140ºF Tooling Time (Working Time) 5-10 minutes Tack Free Time 10-20 minutes Full Cure 24 hours Return to Service Time 12 hours Vertical Sag (ASTM D2202) 0.05” Typical Cured Performance Properties Service Temperature Range -40ºF to 350°F continuous use, up to 400ºF intermittent use after full cure Water Ready Time 12 hours Paint Ready Time Not paintable TYPICAL PHYSICAL & CHEMICAL PROPERTIES 3/3/2019 Mildew Resistance Cured sealant is mold & mildew resistant Dynamic Joint Movement (ASTM C719) +/-25% Remove excess uncured sealant from surfaces and tools with mineral spirits. Excess cured sealant must be cut or scraped away. Do not use mineral spirits to clean hands or skin. Wash hands or skin with soap and water. Store container in temperatures below 80ºF and in a dry place. See product label or Safety Data Sheet (SDS) for health and safety information. You can request a SDS by visiting our website at dap.com or calling 888-DAP-TIPS. WARRANTY: If product fails to perform when used as directed, within one year of date of purchase, call 888-DAP-TIPS, with your sales receipt and product container available, for replacement product or sales price refund. DAP Products Inc. will not be responsible for incidental or consequential damages. Manufactured for: DAP Products Inc., 2400 Boston Street, Baltimore, Maryland 21224 Usage Information: Call 888-DAP-TIPS or visit dap.com & click on “Ask the Expert” Order Information: 800-327-3339 or orders@dap.com Fax Number: 410-558-1068 Also, visit the DAP website at dap.com CLEAN UP & STORAGE SAFETY WARRANTY COMPANY IDENTIFICATION 09 6700 - FLUID-APPLIED FLOORING Workmanship Warranty 09 6700 - FLUID-APPLIED FLOORING Maintenance Information Technical Bulletin No. 99-18 May 1999 Page 1 of 2 SUBJECT Protection and Maintenance of Tnemec Polymer Floorings PURPOSE To instruct facility personnel on the recommended procedure for maintenance cleaning of polymer floors. GENERAL Tnemec flooring systems will benefit from a regular maintenance program. All floors will show wear, becoming less attractive by physical and chemical abuse over a period of time. However, a regular maintenance schedule that removes dirt and chemical residue will prolong the life of the floor. In addition to thorough cleaning, the periodic application of waxes, acrylics or polishes will tend to isolate the flooring system from physical attack and maintain the performance of the floor. Initial Procedure: Polymer flooring systems typically require five or more days at 75°F. before becoming fully cured. Optimum physical strength and chemical resistance depend upon the drying or curing conditions. During this curing period the surface should be protected by limiting traffic exposure or by covering with protective paper or plywood. General Maintenance: The frequency of the maintenance procedure is dependent upon the volume and type of traffic. The following is a guide for establishing a general maintenance program: • Frequently sweep or dust utilizing a commercial sweeping compound. • At regular intervals, wash floor using warm/hot potable water with mild cleaning solutions containing ammonia or alcohol bases, or detergents such as tri-sodium phosphate. Avoid abrasives. Cleaning may be done with pressure washing equipment (max. 1,000 psi, 2 gpm delivery), or by hand scrubbing with soft bristled brushes or sponges. For heavy stains, a floor buffing machine afixed with a soft bristle or soft scrub pad may be used. T NEMETECH TNEMEC COMPANY INCORPORATED Technical Bulletin No. 99-18 May 1999 Page 2 of 2 • Rinse the entire area with clean running water whenever possible. Squeegee to drain or pick up with a wet vacuum to remove all residual contaminants. • If gloss level is to be restored after use, apply a water-based non-ambering liquid floor finish (acrylic or urethane). To remove the finish, apply an ammoniated heavy-duty stripper-rinse and allow to dry before refinishing. Local janitorial supply houses may recommend systems. Select a reputable manufacturer. Dubois, Hillyard or Oakite® are well-known. • Epoxy and urethane finishes are not affected by the cleaning operation, however epoxies tend not to retain their gloss levels as well as urethanes. The need to apply sealer coats for gloss rejuvenation is totally dependent upon the owner’s preference. Recoating/Refinishing: Uniformly scarify the entire surface to be coated with a medium-grit sandpaper (120-150 grit). Reapply specified system in accordance with manufacturer’s application recommendations. If practical, use a break in the surface plane as a stopping point for the repair, i.e., seams, expansion joints, control joints, etc. Use the product literature as a reference for proper mixing, application and handling. JS 09 6700 - FLUID-APPLIED FLOORING Product Information Starting Line Floor Coatings, Inc. 14608 Felton Court Suite #102 Apple Valley, MN 55124 Phone: 952-882-9498 / Fax: 952-736-8376 5 Sullivan Brothers Convention Center SUBMITTAL DATA SHEET Date: 12/5/19 Project Name: 5 Sullivan Brothers Convention Center To: Ana Seaman Henkel Construction Co. 208 East State Street Mason City, IA 50401 From: Kelly DeMorett Starting Line Floor Coatings, Inc. 14608 Felton Court Ste. 102 Apple Valley, MN 55124 Architect: Invision 501 Sycamore St. Ste. 101 Waterloo, IA 50703 The following complete sets of data sheets are submitted for overall project Review and action: 09 67 00 Fluid-Applied Flooring Tnemec Series 245, 246 Starting Line Floor Coatings, Inc. 14608 Felton Court Suite #102 Apple Valley, MN 55124 Phone: 952-882-9498 / Fax: 952-736-8376 5 Sullivan Brothers Convention Center SYSTEM DATA SHEET System Number: 09 67 00 System Title: Fluid-Applied Flooring Manufacturer: Tnemec Supplier: Tnemec Mfg. Representative Name: Kevin Renslow Surface Preparation: Shot blast the surface of the floor to obtain a minimum profile of IRCI-CSP 4-6 Paint Material/Product Name & Number/Coverage: COVE BASE: 1. 4” high base w/ ¾” radius 2. Snap a tape line horizontally to the wall surface to form a controlled edge for placement of the cove base 3. Trowel up material 4” onto wall surface FLOOR: 1. ¼” overall thickness 2. Topping – Series 245 – 30 sq. ft. per gal. 3. Broadcast Flintshot 4. Topcoat – Series 246 – 100 sq. ft. per gal. ULTRA-TREAD ® S PRODUCT DATA SHEET SERIES 245 PRODUCT PROFILE GENERIC DESCRIPTION Polyurethane Modified Concrete COMMON USAGE Ultra-Tread S is a low odor, slurry applied floor topping designed for monolithic applications in abusive service areas. It provides superior performance to other flooring systems such as acid brick, quarry tile and most polymer flooring systems. Designed for use in food and beverage facilities, pharmaceutical and processing areas, commercial and restaurant kitchens or anywhere a durable floor topping is required. Provides excellent chemical resistance and withstands thermal shock due to hot liquids and aggressive cleaning procedures. Areas may be quickly returned to service within hours of installation, depending on temperature and humidity. Ultra-Tread S is a self-priming base coat that can be applied to 10 day old concrete. It can withstand moisture vapor transmission up to 20 lbs (per ASTM F 1869) and relative humidity up to 99% (per ASTM F 2170). This unique self-leveling mortar system is typically applied by trowel or screed, backrolled with a loop roller and broadcast to refusal with 30/50 mesh aggregate, colored quartz or decorative flake. Note: Series 245 can be applied as a stand-alone mortar. If topcoating, the mortar, while still wet, must be broadcast to refusal with aggregate, color quartz or decorative flake typically completed within 10 to 15 minutes of application. Color quartz and/or decorative flake systems will require an additional broadcast layer using Series 222, 224, 237, 238 or 256 clear to obtain a uniform appearance and texture before applying the desired clear finish coats. This will typically result in a total system thickness of 1/4"-5/16". COLORS 00GR Gray, 00RD Red. Black, blue, beige, and green are also available. Additional lead time may apply. Aromatic urethanes chalk and yellow with age, extended exposure to UV and artificial lighting. Note: Colored quartz or decorative flake may be broadcast to refusal into the system, creating a multi-colored or tweed look. A variance in color may be noticeable and require a second broadcast layer of colored quartz or decorative flake. A sample is recommended for color selection. FINISH Matte SPECIAL QUALIFICATIONS Formulated with antimicrobial properties. Does not support bacteria or fungal growth. Contact your Tnemec representative for specific test results. Series 245 was tested in accordance with, and passed, the California Department of Public Health CDPH/EHLB/Standard Method Version 1.1, 2010 emissions testing and meets qualifications of LEED v4, Collaborative for High Performance Schools, and Living Building Challenge. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. © January 31, 2018 by Tnemec Company Inc. COATING SYSTEM SURFACER/FILLER/PATCHER Series 243, 244 or Series 245 (extended with aggregate). Patching should be allowed to cure a minimum of six hours prior to placement of the Series 245 to avoid blistering or doming of the Series 245. Series 215, or 201 mixed with fumed silica, may be used for small patches or crack repairs. Certain high-early strength, cementitious repair mortars are also acceptable. Contact Tnemec for further qualifications. PRIMERS Self-priming INTERMEDIATE Series 222, 223, 224, 237, 238, 239, 252SC, 256. Note: Series 245 must be broadcast to refusal with aggregate, colored quartz or decorative flake if topcoating. Broadcast aggregate or colored quartz at an approximate rate of 0.5 lb per sq ft and decorative flake at an approximate rate of 0.25 lb per sq ft. The Series 245 base coat will account for approximately 1/4" of the desired system thickness. TOPCOATS Series 237, 238, 239, 246, 247, 248, 252SC, 256, 280, 282, 284, 285, 286, 290, 291, 294, 295, 296, 297. Note: These topcoats may only be used when recommended aggregate has been broadcast to refusal into the wet Series 245 or the cured surface of the Series 245 has been cleaned and thoroughly abraded by sanding or grinding prior to topcoating. Note: If Series 247 (tinted), 248 (tinted), 290, 291 or 297 is selected for the finish coat over a broadcast system, a grout coat of Series 237 or 238 (tinted), 256 (tinted), 280 or 281 is required. If Series 247 (clear), 248 (clear), 285, 294, 295 or 296 is selected for the finish coat over a broadcast system, a grout coat of 237 or 238 (clear), 256 (clear) or 284 is required. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. SURFACE PREPARATION Prepare surfaces by method suitable for exposure and service. CONCRETE Allow new poured-in-place concrete to cure a minimum of 10 days at 75°F (24°C). Verify concrete dryness in accordance with ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed 20 pounds per 1,000 square feet in a 24 hour period), F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes” (relative humidity should not exceed 99%), or D 4263 “Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method” (no moisture present). Note: The testing listed above cannot guarantee avoidance of future moisture related problems particularly with existing concrete slabs. This is especially true if the use of an under slab moisture vapor barrier cannot be confirmed or concrete contamination from oils, chemical spills, unreacted silicates, chlorides or Alkali Silica Reaction (ASR) is suspected. Prepare concrete surfaces in accordance with NACE No. 6/SSPC-SP13 Joint Surface Preparation Standards and ICRI Technical Guidelines. Abrasive blast, shot-blast, water jet or mechanically abrade concrete surfaces to remove laitance, curing compounds, hardeners, sealers and other contaminants and to provide a minimum ICRI-CSP 5 or greater surface profile. Large cracks, voids and other surface imperfections should be filled with a recommended filler or surfacer. ALL SURFACES Must be clean, dry and free of oil, grease and other contaminants. Note: Substrate conditions which can adversely affect the adhesion of Series 245 Ultra-Tread S include: concrete that is structurally unsound, wet, damp, contaminated, or inadequately profiled at the time of application, absent or inadequate under slab moisture vapor barrier, hydrostatic pressure, Alkali Silica Reaction (ASR), and migration of oils, chemicals, and other contaminants. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. Page 1 of 3 TECHNICAL DATA VOLUME SOLIDS 100% (mixed) RECOMMENDED DFT 3/16" to 1/4" (5 mm to 6 mm). Series 245 can be applied as a stand alone mortar (neat) at 3/16"-1/4" (5 mm - 6 mm). Broadcasting with aggregate to refusal at 3/16" (5 mm) neat will yield a total thickness of 1/4" (6 mm), at 1/4" (6 mm) neat will yield a total thickness of 5/16" (8 mm). Important: Series 245 should not exceed 1/2" (13 mm) thickness when applied neat. Refer to coverage rates table for more information. Note: Exceeding the recommended coating thickness may result in blistering of the product. Avoid excessive coating thickness by thoroughly filling voids, depressions and cracks with recommended filler or surfacer prior to Series 245 application. CURING TIME Temperature Min. Recoat Light Traffic Place In Service † 75°F (24°C)6 hours 8 hours 12 hours † For full resistance to chemicals and steam cleaning, 24 hour cure is needed. Curing time varies with surface temperature, air movement, humidity and film thickness. Note: For faster curing and low temperature applications, add No. 44-714 Ultra-Tread Accelerator, see separate product data sheet for cure information. VOLATILE ORGANIC COMPOUNDS Parts A & B: 0.16 lbs/gallon (19 grams/litre) Parts A, B & C: 0.07 lbs/gallon (8 grams/litre) THEORETICAL COVERAGE 23 sq ft per small kit at 1/4" 31 sq ft per small kit at 3/16" NUMBER OF COMPONENTS Four—Liquids: Part A & Part B, Aggregate: Part C, Colorant PACKAGING PART A PART B PART C (Aggregate) Colorant (Powder) Mixed Yield Small Kit 1-1 gallon jug (partially filled) 1-1 gallon jug (partially filled) 1-42.5 lb. bag 1 bag 3.6 gal. NET WEIGHT PER GALLON 16.28 ± 0.25 lbs (7.38 ± .11 kg) (mixed) STORAGE TEMPERATURE Minimum 35°F (2°C) Maximum 110°F (43°C) Material should be stored at temperatures between 70°F and 90°F (21°C and 32°C) for at least 48 hours prior to use. TEMPERATURE RESISTANCE (Dry) Continuous 235°F (112°C). At thicknesses of ¼” or greater, resistant to aggressive chemical cleaning, thermal shock from steam or hot water, and occasional high temperature liquid spills or discharge at temperatures from -40°F (-40°C) to 250°F (121°C). SHELF LIFE Part A: 12 months Part B: 12 months Part C: 12 months FLASH POINT - SETA N/A HEALTH & SAFETY This product contains chemical ingredients which are considered hazardous. Read container label warning and Material Safety Data Sheet for important health and safety information prior to the use of this product. Keep out of the reach of children. © January 31, 2018 by Tnemec Company Inc. PRODUCT DATA SHEET ULTRA-TREAD ® S | SERIES 245 APPLICATION COVERAGE RATES Before commencing, obtain and thoroughly read the StrataShield Application Guide for Polyurethane Modified Concrete. Applied Neat Broadcast To Refusal Small Kit Coverage 3/16” (5 mm)1/4" (6 mm) 31 sq ft (2.8 m²) 1/4" (6 mm)5/16" (8 mm)23 sq ft (2.1 m²) Important: Series 245 should not exceed 1/2" (13 mm) thickness when applied neat. Note: Exceeding the recommended coating thickness may result in blistering of the product. Avoid excessive coating thickness by thoroughly filling voids, depressions and cracks with recommended filler or surfacer. Application below minimum or above maximum recommended thicknesses may adversely affect performance. Above rates are based on theoretical coverage. Actual coverage will vary based on condition of substrate. MIXING Using a variable speed drill and mixing paddle, slowly mix the entire contents of both the A and B components for a minimum of one minute. While under agitation, slowly add colorant and mix until blended. Continuing agitation, slowly add the Part C aggregate and mix until material is uniform and no dry aggregate is present. The entire mixing process should take approximately three minutes. Note: Part B is moisture sensitive. Do not open until ready to mix. Caution: Do not attempt to split kits and do not reseal mixed material. Accelerator: For accelerated cure on low temperature applications add Series 44-714 Ultra-Tread Accelerator to the Series 245 Part A prior to mixing. The proper amount of Series 44-714 is based upon ambient temperature; At 68°F (20°C) with 40% relative humidity 1 oz per kit will result in an 8 hour maximum cure time, 2 oz per kit will result in a 6 hour maximum cure time, 3 oz per kit will result in a 4 hour maximum cure time. Note: Material will set up quickly if not applied immediately after mixing. THINNING DO NOT THIN. POT LIFE Without 44-714: 15 minutes at 75°F (24°C) Higher material temperatures will significantly reduce the pot life and working time. With 44-714 when using maximum amount (3 oz): 15 minutes at 60°F (16°C) 10 minutes at 70°F (21°C) APPLICATION EQUIPMENT Apply: Trowel or screed rake. Finish: Porcupine roller or loop roller. Note: For detailed instructions, refer to the StrataShield Application Guide for Polyurethane Modified Concrete. SURFACE TEMPERATURE Minimum of 40°F (4°C), optimum 65°F to 80°F (18°C to 27°C), maximum of 85°F (29°C). The substrate temperature should be at least 5°F (3°C) above the dew point. Coating will not cure below minimum surface temperature. MATERIAL TEMPERATURE For optimum application, handling and performance, the material temperature during application should be between 60°F and 80°F (16°C and 27°C). Temperature will affect the workability. Cool temperatures increase viscosity and decrease workability. Warm temperatures will decrease viscosity and significantly shorten pot life and working time. AMBIENT HUMIDITY Humidity must be below 85%. Page 2 of 3 CLEANUP Flush and clean all equipment immediately after use with xylene or MEK. © January 31, 2018 by Tnemec Company Inc. PRODUCT DATA SHEET ULTRA-TREAD ® S | SERIES 245 WARRANTY & LIMITATION OF SELLER'S LIABILITY: Tnemec Company, Inc. warrants only that its coatings represented herein meet the formulation standards of Tnemec Company, Inc. THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. The buyer's sole and exclusive remedy against Tnemec Company, Inc. shall be for replacement of the product in the event a defective condition of the product should be found to exist and the exclusive remedy shall not have failed its essential purpose as long as Tnemec is willing to provide comparable replacement product to the buyer. NO OTHER REMEDY (INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO THE BUYER. Technical and application information herein is provided for the purpose of establishing a general profile of the coating and proper coating application procedures. Test performance results were obtained in a controlled environment and Tnemec Company makes no claim that these tests or any other tests, accurately represent all environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection and use of the coating. Tnemec Company Inc. 6800 Corporate Drive Kansas City, Missouri 64120-1372 1-800-TNEMEC1 Fax: 1-816-483-3969 www.tnemec.com PDS245 Page 3 of 3 ULTRA-TREAD ® GLAZE PRODUCT DATA SHEET SERIES 246 PRODUCT PROFILE GENERIC DESCRIPTION Modified Polyurethane COMMON USAGE Ultra-Tread Glaze is a pigmented, high-build, low odor, polyurethane coating. Typically used as a topcoat for sealing or locking aggregate in Ultra-Tread S broadcast texture finishes. Designed for use in food and beverage facilities, pharmaceutical and processing areas, commercial and restaurant kitchens or anywhere a durable floor topping is required. Provides excellent chemical resistance and withstands thermal shock due to hot liquids and aggressive cleaning procedures. Areas may be quickly returned to service within hours of installation, depending on temperature and humidity. COLORS 00GR Gray, 00DG Dark Gray, 00RD Red. Special colors are available. Please contact your Tnemec representative for additional information. Aromatic urethanes chalk and yellow with age, extended exposure to UV and artificial lighting. A sample is recommended for color selection. FINISH Matte SPECIAL QUALIFICATIONS Formulated with antimicrobial properties. Does not support bacteria or fungal growth. Contact your Tnemec representative for specific test results. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. © July 27, 2017 by Tnemec Company Inc. COATING SYSTEM INTERMEDIATE Series 241, 242, 243, 244, 245. Note: Use Series 246 as a topcoat only when recommended aggregate has been broadcast to refusal into the surface of the Series 245 or the cured surface of the Series 242, 243, 244 or 245 has been thoroughly cleaned and abraded by sanding or grinding prior to topcoating. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. SURFACE PREPARATION Prepare surfaces by method suitable for exposure and service. CONCRETE Allow new poured-in-place concrete to cure a minimum of 28 days at 75°F (24°C). Verify concrete dryness in accordance with ASTM F 1869 “Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride” (moisture vapor transmission should not exceed three pounds per 1,000 square feet in a 24 hour period), F 2170 “Standard Test Method for Determining Relative Humidity in Concrete using in situ Probes” (relative humidity should not exceed 80%), or D 4263 “Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method” (no moisture present). Note: The testing listed above cannot guarantee avoidance of future moisture related problems particularly with existing concrete slabs. This is especially true if the use of an under slab moisture vapor barrier cannot be confirmed or concrete contamination from oils, chemical spills, unreacted silicates, chlorides or Alkali Silica Reaction (ASR) is suspected. Prepare concrete surfaces in accordance with NACE No. 6/SSPC-SP13 Joint Surface Preparation Standards and ICRI Technical Guidelines. Abrasive blast, shot-blast, water jet or mechanically abrade concrete surfaces to remove laitance, curing compounds, hardeners, sealers and other contaminants and to provide a minimum ICRI-CSP 5 or greater surface profile. Large cracks, voids and other surface imperfections should be filled with a recommended filler or surfacer. ALL SURFACES Must be clean, dry and free of oil, grease and other contaminants. Existing coatings require thorough scarification using a power sander with 100 grit sandpaper and compatibility testing. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. TECHNICAL DATA VOLUME SOLIDS 85% ± 2.0% RECOMMENDED DFT Suggested 8.0 to 10.0 mils (203 to 254 microns). CURING TIME Temperature Light Traffic Place in Service ‡ 75°F (24°C)8 hours 12 hours ‡ For full resistance to chemicals and steam cleaning, 24 hour cure is needed. Curing time varies with surface temperature, air movement, humidity and film thickness. Note: For faster curing and low temperature applications, add No. 44-714 Ultra-Tread Accelerator, see separate product data sheet for cure information. VOLATILE ORGANIC COMPOUNDS Parts A & B: 0.2 lbs/gallon (23 grams/litre) Parts A, B, C & D: 0.16 lbs/gallon (19 grams/litre) THEORETICAL COVERAGE 1,379 mil sq ft/gal (33.9 m²/L at 25 microns). See APPLICATION for coverage rates. NUMBER OF COMPONENTS Four—Liquids: Parts A, B & D, Aggregate: Part C PACKAGING PART A (Partially filled) PART B (Partially filled) PART C (Aggregate) PART D (Liquid Colorant)Mixed Yield Small Kit 1-1 gallon jug 1-1/2 gallon jug 1-4.5 lb. bag 1-1/2 pint container 1.2 gal. NET WEIGHT PER GALLON 11.90 ± 0.25 lbs (5.40 ± .11 kg) (mixed) STORAGE TEMPERATURE Minimum 35°F (2°C) Maximum 110°F (43°C) Note: Material should be stored at temperatures between 70°F and 90°F (21°C and 32°C) for at least 48 hours prior to use. TEMPERATURE RESISTANCE Continuous 235°F (112°C) SHELF LIFE Part A: 12 months Part B: 12 months Part C: 12 months FLASH POINT - SETA N/A HEALTH & SAFETY This product contains chemical ingredients which are considered hazardous. Read container label warning and Safety Data Sheet for important health and safety information prior to the use of this product. Keep out of the reach of children. Published technical data and instructions are subject to change without notice. The online catalog at www.tnemec.com should be referenced for the most current technical data and instructions or you may contact your Tnemec representative for current technical data and instructions. Page 1 of 2 APPLICATION COVERAGE RATES Before commencing, obtain and thoroughly read the StrataShield Application Guide for Polyurethane Modified Concrete. Dry Mils (Microns)Wet Mils (Microns)Small Kit Coverage Suggested 9.0 (230)10.5 (265)151 (14.2) Minimum 8.0 (205)9.5 (240)170 (16.0) Maximum 10.0 (255)11.5 (290)136 (12.8) Application of coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating performance. Above rates are based on theoretical coverage. Actual coverage will vary based on condition of substrate. MIXING Using a variable speed drill and mixing paddle, slowly mix the entire contents of both the A and B components for a minimum of one minute. While under agitation, slowly add colorant and mix until blended. Continuing agitation, slowly add the Part C aggregate and mix until material is uniform and no dry aggregate is present. The entire mixing process should take approximately three minutes. Note: Part B is moisture sensitive. Do not open until ready to mix. Caution: Do not attempt to split kits and do not reseal mixed material. Accelerator: For accelerated cure on low temperature applications add Series 44-714 Ultra-Tread Accelerator to the Series 246 Part A prior to mixing. The proper amount of Series 44-714 is based upon ambient temperature; At 68°F (20°C) with 40% relative humidity 1 oz per kit will result in an 8 hour maximum cure time, 2 oz per kit will result in a 6 hour maximum cure time, 3 oz per kit will result in a 4 hour maximum cure time. Note: Material will set up quickly if not applied immediately after mixing. THINNING DO NOT THIN. POT LIFE Without 44-714: 10 minutes at 75°F (24°C) Higher material temperatures will significantly reduce the pot life and working time. With 44-714 when using maximum amount (3 oz): 15 minutes at 60°F (16°C) 10 minutes at 70°F (21°C) APPLICATION EQUIPMENT Brush, roller, trowel and squeegee. Squeegee or trowel to spread material and backroll. Brush small areas only. Roller: Use high quality 3/8" to 1/2" nap shed resistant woven fabric cover. Brush: Use high quality synthetic or nylon bristle brush. Note: For detailed instructions, refer to the StrataShield Application Guide for Polyurethane Modified Concrete. TEMPERATURE REQUIREMENT Surface Temperature: Minimum of 40°F (4°C), optimum 65°F to 80°F (18°C to 27°C), maximum of 85°F (29°C). The substrate temperature should be at least 5°F (3°C) above the dew point. Coating will not cure below minimum surface temperature. Material Temperature: For optimum application, handling and performance, the material temperature during application should be between 60°F and 80°F (16°C and 27°C). Temperature will affect the workability. Cool temperatures increase viscosity and decrease workability. Warm temperatures will decrease viscosity and significantly shorten pot life and working time. AMBIENT HUMIDITY Humidity must be below 85%. CLEANUP Flush and clean all equipment immediately after use with xylene or MEK. © July 27, 2017 by Tnemec Company Inc. PRODUCT DATA SHEET ULTRA-TREAD ® GLAZE | SERIES 246 WARRANTY & LIMITATION OF SELLER'S LIABILITY: Tnemec Company, Inc. warrants only that its coatings represented herein meet the formulation standards of Tnemec Company, Inc. THE WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. The buyer's sole and exclusive remedy against Tnemec Company, Inc. shall be for replacement of the product in the event a defective condition of the product should be found to exist and the exclusive remedy shall not have failed its essential purpose as long as Tnemec is willing to provide comparable replacement product to the buyer. NO OTHER REMEDY (INCLUDING, BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO THE BUYER. Technical and application information herein is provided for the purpose of establishing a general profile of the coating and proper coating application procedures. Test performance results were obtained in a controlled environment and Tnemec Company makes no claim that these tests or any other tests, accurately represent all environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection and use of the coating. Tnemec Company Inc. 6800 Corporate Drive Kansas City, Missouri 64120-1372 1-800-TNEMEC1 Fax: 1-816-483-3969 www.tnemec.com PDS246 Page 2 of 2 Shop Drawing Submittal Project: 5 Sullivan Brothers Convention Center – Kitchen Remodel Location: Waterloo, Iowa Architect: InVision Architecture MEP Engineer: Modus Engineering General Contractor: Henkel Construction Date: Submitted By: Item Submitted: (Comments in RED)(Comments in BLUE)(Comments in ORANGE) X 1/20/20 Ana Seaman 1/20/20 1/20/20Starting Line Floor Coatings096700 Fluid-Applied FlooringSamples - REVISED ULTIMATE SEAMLESS FLOOR TOPPING ULTRA-TREAD Daily productivity means hard abuse on any facility’s floor. In addition to foot traffic and moving heavy loads, floors also deteriorate quickly due to repeated chemical abuse, wet environments, and drastic temperature changes, which put you and your assets at risk. The solution: Ultra-Tread. The fast, effective flooring system from Tnemec Company’s StrataShield® family of products. A polyurethane modified concrete floor topping, Ultra-Tread is designed for fast installation and quick return-to-service, limiting costly downtime. It’s an ideal flooring solution for USDA- and FDA-regulated facilities, and offers excellent resistance to thermal shock, chemicals, and the high-alkalinity usually associated with moisture vapor transmission (MVT). Contact your local Tnemec coatings consultant for detailed system information. ULTRA-TREAD A versatile and self-priming floor topping that withstands hot liquids and aggressive cleanings, Ultra-Tread is ideally suited to meet conditions in food and beverage processing plants, meat and poultry plants, pharmaceutical manufacturing, paper facilities, commercial/industrial kitchens, or anywhere a durable floor topping is required. Available in three distinct versions, as well as a glaze coat, there is an Ultra-Tread product for all your flooring needs. SERIES 243 ULTRA-TREAD V A trowelable material for vertical surfaces such as trenches, equipment pads, and coves, Series 243 provides a seamless floor to wall transition. This product is used in conjunction with Series 244 and Series 245 and provides a smooth surface finish. SERIES 244 ULTRA-TREAD M A trowelable mortar with high early strength, Series 244 is typically used to resurface floors degraded by physical or chemical attack. This product provides a slightly textured finish and is typically installed as a stand-alone system with a nominal 1⁄4” to 3⁄8” thickness. SERIES 245 ULTRA-TREAD S A versatile slurry, Series 245 is typically installed at a nominal thickness of 3/16” to 1/4”. This product can be applied as a stand-alone flooring system, or sand, aggregate, or decorative colored quartz can be broadcast into it to modify its texture or appearance. A variety of clear or pigmented topcoats may be applied to seal the system. SERIES 246 ULTRA-TREAD GLAZE A pigmented, high-build polyurethane, Series 246 is typically used as a topcoat to seal Series 245 textured floors. Published technical instructions and pricing are subject to change without notice. Contact your Tnemec technical representative for current technical data, instructions and pricing. Warranty Information: The service life of Tnemec coatings will vary. For warranty, limitation of seller’s liability and product information, please refer to Tnemec Product Data Sheets at www.tnemec.com or contact your Tnemec technical representative. © Tnemec Company, Inc. 2016 HW2.5M616 FLYUT INNOVATION IN EVERY COAT ™ Series 245 Ultra-Tread S can also be broadcast with quartz for a decorative appearance and then coated with a clear chemical resistant sealer. A second quartz broadcast may be required to achieve uniform color and texture. For standard quartz blend options, see the StrataShield Decorative Quartz color card. 00GR Gray 00RD Red CHEMICAL RESISTANCE STANDARD COLORS Also available in black, blue, beige, green and safety yellow. Additional lead time may apply. Tnemec Company Inc. 6800 Corporate Drive Kansas City, Missouri 64120-1372 1-800-TNEMEC1 Fax: 816-483-3969 tnemec.com Ultra-Tread flooring products offer excellent resistance to chemicals at various concentrations. To determine which Tnemec product is best suited for your particular exposure conditions, contact your local Tnemec representative at tnemec.com. PINNACLE BANK ARENA To protect the floors in the kitchen and food storage areas at the home of The University of Nebraska-Lincoln basketball teams, the project team selected Series 245 Ultra-Tread S as part of a chemical- and abrasion-resistant flooring system. Applicators began with a base coat of Series 245, broadcast with decorative quartz, and finished the system with a topcoat of Series 248 Everthane, an extremely hard, chemical-resistant urethane coating. These products provide the concrete with an aesthetically pleasing and cleanable surface that will hold up to the rough kitchen environment. 22 0050 - BASIC PLUMBING REQUIREMENTS General Plumbing Warranty 22 1116 - DOMESTIC PLUMBING PIPING PEX Warranty UPONOR, INC. LIMITED WARRANTY Valid for Uponor AquaPEX-a® Tubing, ProPEX® and Other Select Plumbing Products This Warranty is Effective For Installations Made After October 15, 2012 Subject to the terms and conditions of this Limited Warranty, Uponor, Inc. (“Uponor”) warrants to the owner of the applicable real property that the Uponor products listed below shall be free from defects in materials and workmanship, under normal conditions of use when installed as part of a potable water distribution system. Unless otherwise specified, this Limited Warranty for the applicable Uponor products shall commence on the date the product was installed (“Commencement Date”) and will expire after the following number of years: (a) Twenty-Five (25) years for Uponor AquaPEX-a® tubing, Uponor ProPEX® fittings and ProPEX® rings when all are installed in combination with each other; (b) Ten (10) years for Uponor AquaPEX-a® tubing when installed in combination with non-Uponor fittings; (c) Ten (10) years for Uponor EP valves, EP valveless manifolds and Uponor tub ells, stub ells, and straight stubs; (d) Two (2) years for Uponor metal manifolds, Uponor EP manifolds with valves; (e) Five (5) years for the Uponor D’MAND® system; (f) Two (2) years for all other components of the Uponor ProPEX® fitting system and all other plumbing items listed in Uponor’s catalog as of the effective date of this limited warranty. For purposes of this warranty, the use of Uponor AquaPEX-a® tubing, Uponor ProPEX® fittings and ProPEX® rings in combination with each other shall constitute an Uponor ProPEX® system. Exclusions From Limited Warranty: This limited warranty applies only if the applicable Uponor products identified above: (a) are selected, configured and installed by a certified licensed plumbing contractor recognized by Uponor as having successfully completed the Uponor AquaPEX® training course and according to the installation instructions provided by Uponor; (b) are not exposed to temperatures and/or pressures that exceed the limitations printed on the warranted Uponor product or in the applicable Uponor installation manual; (c) remain in their originally installed location; (d) are connected to potable water supplies; (e) show no evidence of misuse, tampering, mishandling, neglect, accidental damage, modification or repair without the approval of Uponor; and (f) are installed in accordance with then-applicable building, mechanical, plumbing, electrical and other code requirements; (g) are installed in combination with Uponor AquaPEX-a® tubing unless otherwise specified below. Without limiting the foregoing, this limited warranty does not apply if the product failure or resulting damage is caused by: (a) faulty installation; (b) components not manufactured or sold by Uponor; (c) exposure to ultra violet light; (d) external physical or chemical conditions, including, but not limited to chemically corrosive or aggressive water conditions; or (e) any abnormal operating conditions. The use of non-Uponor termination devices such as tub/shower valves, sill cocks, stops and other similar components that attach at the termination or end-point of a run or branch of Uponor AquaPEX-a® tubing does not disqualify the additional parts of the Uponor ProPEX® fitting system from the terms of this Limited Warranty. Only the non-Uponor termination devices themselves are excluded from the Uponor Limited Warranty. The use of non-Uponor AquaPEX-a® tubing disqualifies any and all parts of the Uponor ProPEX fitting® system from the terms of this Limited Warranty. This exclusion does not include certain circumstances wherein Uponor AquaPEX-a® tubing is installed in combination with CPVC, copper, PPr , or stainless steel pipe risers as may be required in limited residential and commercial plumbing applications. The use of non-Uponor fittings in combination with Uponor ProPEX® fittings disqualifies Uponor ProPEX fittings® from the terms of this Limited Warranty. PLUMBING SYSTEMS WARRANTY Warranty Claim Process (for building owners and homeowners only): Written notification of an alleged failure of, or defect in, any Uponor part or product identified herein should be sent to Uponor, Attn: Warranty Department, 5925 148th Street West, Apple Valley, Minnesota 55124 or by facsimile to (866) 351-8402, and must be received by Uponor within thirty (30) days after detection of an alleged failure or defect occurring within the applicable warranty period. All products alleged to be defective must be sent to Uponor for inspection and testing for determination of the cause of the alleged failure or defect. Exclusive Remedies: If Uponor determines that a product identified herein has failed or is defective within the scope of this limited warranty, Uponor’s liability is limited, at the option of Uponor, to: issue a refund of the purchase price paid for, or to repair or replace the defective product. Notwithstanding anything to the contrary in this limited warranty, if Uponor determines that any damages to the real property in which a defective product was installed were the direct result of a leak or failure caused by a manufacturing defect in an Uponor product covered by this limited warranty and occurring within the first ten (10) years after the applicable Commencement Date or during the applicable limited warranty period, whichever is shorter, and if the claimant took reasonable steps to promptly mitigate (i.e., limit or stop) any damage resulting from such failure, then Uponor may at its discretion, reimburse claimant for the reasonable costs of repairing or replacing such damaged real property, including flooring, drywall, painting, and other real property damaged by the leak or failure. Uponor shall not pay for any other additional costs or expenses, including but not limited to, transportation, relocation, labor, repairs or any other work associated with removing and/or returning failed or defective products, installing replacement products, damage to personal property or damage resulting from mold. Warranty Claim Dispute Process: In the event claimant and Uponor are unable to resolve a claim through informal means, the parties shall submit the dispute to the American Arbitration Association or its successor (the “Association”) for arbitration, and any arbitration proceedings shall be conducted before a single arbitrator in the Minneapolis, Minnesota metropolitan area. NOTWITHSTANDING THE FOREGOING, NEITHER THE CLAIMANT NOR UPONOR, INC. SHALL BE ENTITLED TO ARBITRATE ANY CLAIMS AS A REPRESENTATIVE OR MEMBER OF A CLASS, AND NEITHER THE CLAIMANT NOR UPONOR SHALL BE ENTITLED TO JOIN OR CONSOLIDATE CLAIMS WITH ANY OTHER PARTIES IN ARBITRATION OR IN LITIGATION BY CLASS ACTION OR OTHERWISE. Transferability: This limited warranty may only be assigned by the original owner of the applicable real property and may not be assigned or transferred after the period ending ten (10) years following the Commencement Date. Miscellaneous: By the mutual agreement of the parties, it is expressly agreed that this limited warranty and any claims arising from breach of contract, breach of warranty, tort, or any other claim arising from the sale or use of Uponor’s products shall be governed and construed under the laws of the State of Minnesota. It is expressly understood that authorized Uponor sales representatives, distributors, and plumbing professionals have no express or implied authority to bind Uponor to any agreement or warranty of any kind without the express written consent of Uponor. THIS LIMITED WARRANTY IS THE FULL EXTENT OF EXPRESS WARRANTIES PROVIDED BY UPONOR, AND UPONOR HEREBY DISCLAIMS ANY WARRANTY NOT EXPRESSLY PROVIDED HEREIN, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THE PRODUCTS COVERED HEREUNDER. UPONOR FURTHER DISCLAIMS ANY STATUTORY OR IMPLIED WARRANTY OF HABITABILITY. EXCEPT AS OTHERWISE EXPRESSLY STATED IN THIS LIMITED WARRANTY, UPONOR FURTHER DISCLAIMS ANY RESPONSIBILITY FOR LOSSES, EXPENSES, INCONVENIENCES, AND SPECIAL, INDIRECT, SECONDARY, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OR RESULTING IN ANY MANNER FROM THE PRODUCTS COVERED HEREUNDER. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES THE CLAIMANT SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Revised as of 8/2012 Uponor, Inc. 5925 148th Street West Apple Valley, MN 55124 USA Tel: (800) 321-4739 Fax: (952) 891-2008 Web: www.uponor-usa.com 22 1116 - DOMESTIC PLUMBING PIPING PEX Product Information Uponor AquaPEX® White, Straight Length Submittal Information Revision C: Oct. 7, 2009 Project Information Job Name: Location: Part No. Ordered: Engineer: Date Submitted: Contractor: Submitted By: Manufacturer’s Representative: Approved By: Technical Data Material: Crosslinked polyethylene PEX-a Engel Method Standard Grade Hydrostatic Ratings (PPI): 200°F (93°C) at 80 psi 180°F (82°C) at 100 psi 73.4°F (23°C) at 160 psi ½" Uponor AquaPEX® tubing only: 120°F (49°C) at 130 psi Linear Expansion Rate: 1.10"/10°F (12°C)/100' Product Information and Application Use Uponor AquaPEX White, straight length tubing, is used primarily in hot and cold potable water distribution systems and AquaSAFETM Residential Fire Safety systems. 9 Description Part Number A B Weight ½" Uponor AquaPEX White, 20-ft. straight length, 500 ft. F1930500 0.475" 0.625" 28.0 lbs. ¾" Uponor AquaPEX White, 20-ft. straight length, 300 ft. F1930750 0.671" 0.875" 31.0 lbs. 1" Uponor AquaPEX White, 20-ft. straight length, 200 ft. F1921000 0.862" 1.125" 35.0 lbs. 1¼" Uponor AquaPEX White, 20-ft. straight length, 100 ft. F1921250 1.054" 1.375" 32.0 lbs. 1½" Uponor AquaPEX White, 20-ft. straight length, 100 ft. F1921500 1.244" 1.625" 42.0 lbs. 2" Uponor AquaPEX White, 20-ft. straight length, 100 ft. F1922000 1.629" 2.125" 68.1 lbs. 3" Uponor AquaPEX White, 20-ft. straight length, 60 ft. F1923000 2.400" 3.125" 77.0 lbs. Installation Approved fittings are ProPEX® fittings1 for sizes ⅜" through 2" AquaPEX. Use WIPEXTM fittings for 3" AquaPEX. Refer to the AquaPEX Professional Plumbing Installation Handbook or AquaSAFE Fire Safety Installation Guide for additional information. Standards CSA B137.5; ASTM F876; ASTM F877; ASTM F1960; ASTM-E84; ASTM-E119/UL 263 Codes IPC; UPC; NSPC; NPC of Canada Listings ½", ¾”, 1” UL 1821; ULC/ORD - C 199 P; IAPMO; CSA; HUD; WARNOCK HERSEY; NSF; ITS; UL; ICC; PPI; ANSI/NSF 14- and 61-certified; CAN/ULC S102.2; U.S.: ¾" diameter and smaller; Canada: 1" diameter and smaller Related Applications Contact Information PEX-a Plumbing Systems AquaSAFE Residential Fire Safety Systems Uponor, Inc. 5925 148th Street West Apple Valley, MN 55124 USA Phone: (800) 321-4739 Fax: (952) 891-2008 www.uponor-usa.com Uponor Ltd. 2000 Argentia Rd., Plaza 1, Ste. 200 Mississauga, ON L5N 1W1 CANADA Phone: (888) 994-7726 Fax: (800) 638-9517 www.uponor.ca 1ProPEX® is a registered trademark of Uponor, Inc. ProPEX™ is a trademark of Uponor Ltd. 22 4000 - PLUMBING FIXTURES Product Information SUBMITTAL ©2013 Ferguson Enterprises, Inc. All Rights Reserved. 0413 15417 FIVE SULLIVAN BROTHERS KITCHEN IMPROVEMENTS 11/27/2019 Quote # B244915 Customer: BERGEN PLUMBING,INC. Submitted By: Waterloo (Satellite) 920 S Hackett Rd Waterloo, IA 50701 319-235-0222 PageFD13 ZZS4154NH5S ZURN ZS4155S 4NH FLOOR DRAIN W/SS STR 4 FS1 5 ZZ17514NH ZURN 4" 12X12 SS 304 FS 6 TD1 7 EASFT2436SGADA EAGLE GROUP ASFT2436SGADA SS TRENCH DRAIN 8 GI1 10 MSUPER1250 MIFAB SUPERMAX GREASE INTERCEPTOR 1250 GALLONS LIQUID HOLDING CAPACITY 11 ADD AS REQUIRED: MIFABAK MIFAB MIFABAK ANCHOR KIT (SET OF TWO) MIFABC MIFAB MIFABC LID EXTENSION PRICED PER12" MIFABFLC MIFAB MIFAB FLC MEMBRANE CLAMP KIT MIFABSP MIFAB MIFAB SP EXTERNAL SAMPLING PORT EXTERIOR CLEANOUT 12 ZZ1474P ZURN 4 NH HD CO W/ CI CVR 13 ZZ14404NHBP ZURN 4" CO FERRULE W/BRONZE PLUG 14 FCO 15 ZZN14004NH ZURN 4 NH LVL TROL ADJ FLR CO W/ NB TOP 16 MISC SS PIPE & PTRAP 17 GSP16LP IMPORTED 4 SS S10 316L A312 WELD PIPE 18 K22092409 KUSEL 22092409 4" PTRAP SCH10,316SS 19 Page: 2 / 20 FD1 ZZS4154NH5S ZURN ZS4155S 4NH FLOOR DRAIN W/SS STR Page: 3 / 20 Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice SPECIFICATION SHEET TAG _______ * Regularly furnished unless otherwise specified. Zurn Industries, LLC | Specification Drainage Operation 1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax 814-454-7929 In Canada | Zurn Industries Limited 3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax 905-405-1292 www.zurn.com Rev. M Date:09/26/2017 C.N. No.137872 Prod. | Dwg. No.ZS415SS ENGINEERING SPECIFICATION: ZURN ZS415SS Floor and shower drain, Dura-Coated cast iron body with bottom outlet, combination invertible membrane clamp and adjustable collar with seepage slots and "TYPE SS" heel-proof stainless steel medium duty square strainer. OPTIONS (Check/specify appropriate options) PIPE SIZE (Specify size/type) OUTLET 'E' BODY HT. DIM. 2, 3, 4 [51, 76, 102]____ IC Inside Caulk 3-7/8 [98] 2 [51]____ IP Threaded 2-3/8 [60] 3 [76]____ IP Threaded 2-5/8 [67] 4 [102]____ IP Threaded 2-7/8 [73] 2, 3, 4 [51, 76, 102]____ NH No-Hub 3-7/8 [98] 2, 3, 4 [51, 76, 102]____ NL Neo-Loc 3-3/4 [95] PREFIXES ____ ZS D.C.C.I. Body Assembly w/ Square type 304 (CF8) Stainless Steel Top* ____ ZM D.C.C.I. Body Assembly w/ Square type 316 (CF8M) Stainless Steel Top SUFFIXES ____ -AR Acid Resisting Epoxy Coated Cast Iron ____ -G Galvanized Cast Iron ____ -P Trap Primer Connection (Specify 1/2 [13] or 3/4 [19]) ____ -TC Neo-Loc Test Cap Gasket (2, 3, 4 [51, 76, 102] NL Bottom Outlet Only) ____ -U 1 - 3 [25 - 76] High Extension Adapter ____ -V Backwater Valve ____ -VP Vandal-Proof Secured Top ____ -Y Sediment Bucket ZS415SS BODY ASSEMBLY W/ "TYPE SS" STRAINER Dimensions In Inches [mm] A Pipe Size B x B' Strainer Top Size -5SS 2, 3 [51, 76] 5 x 5 [127 x 127] 1 [25] 1-19/32 [40] 1-1/4 [32] 2-3/8 [60] 11 [5] 8-1/2 [55] -6SS 2, 3, 4 [51, 76, 102] 6 x 6 [152 x 152] 1 [25] 1-27/32 [47] 1-13/32 [36] 2-19/32 [66]12 [5-1/2] 13 [84] -8SS 3, 4 [76, 102] 8 x 8 [203 x 203] 1-3/32 [28] 1-7/8 [48] 1-3/4 [44] 2-5/8 [67] 15 [7] 24-1/2 [158] Approx. Wt. Lbs. [kg] Strainer Open Area Sq. In. [cm2] KK' Min.Max.Min.Max. Strainer Designation FD1 Page: 4 / 20 FS1 ZZ17514NH ZURN 4" 12X12 SS 304 FS Page: 5 / 20 www.zurn.com FS1 Page: 6 / 20 TD1 EASFT2436SGADA EAGLE GROUP ASFT2436SGADA SS TRENCH DRAIN Page: 7 / 20 TD1 Page: 8 / 20 TD1 Page: 9 / 20 GI1 MSUPER1250 MIFAB SUPERMAX GREASE INTERCEPTOR 1250 GALLONS LIQUID HOLDING CAPACITY ADD AS REQUIRED: MIFABAK MIFAB MIFABAK ANCHOR KIT (SET OF TWO) MIFABC MIFAB MIFABC LID EXTENSION PRICED PER12" MIFABFLC MIFAB MIFAB FLC MEMBRANE CLAMP KIT MIFABSP MIFAB MIFAB SP EXTERNAL SAMPLING PORT Page: 10 / 20 Page No: Contractor: Purchase Order No: Job Name: Section No: Schedule No: USA: 1-800-465-2736 www.mifab.com CAN: 1-800-387-3880MIFAB® reserves the right to make changes in material and design without formal notice & obligation. CALIFORNIA PROPOSITION 65 WARNING. This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 2019-05-05 ® Location: SUPERMAX® GRAVITY GREASE INTERCEPTORSUPER Speciication: MIFAB® SUPER-_______ gravity grease interceptor with _______ U.S. gallons of liquid holding capacity has a limited lifetime warranty and is made in the U.S.A. out of seamless, rotationally molded High Density Polyethylene with 3/8” uniform wall thickness. Interceptor is designed for above or below ground installation and includes an adjustable lid system, sample port access, internal bale, deep seal trap covered by lid, internal air relief by-pass, stainless steel calibrated oriice plate (internal low control), base for support and loor level installation and 4" no hub inlet and outlet connections. Steel encased composite lids provide a water / gas tight seal and have a minimum of 20,000 LB. load capacity - in accordance with the loading requirements of AASHTO H20. The high density polyethylene material is PE 3135 from Dow 9.39 with a density of 0.939 g/cm3. Note that the interceptor is tested and certiied to the ASME A112.14.3, CSA B481 and ANSI Z1001 Standards and listed with I.A.P.M.O. Function: Used in restaurants, kitchens, institutions, industrial facilities such as food processing and packaging plants and other types of food processing areas where fat, oil and grease (FOG) drains with the waste water. All SuperMax gravity interceptors can withstand a temperature of up to and including 180 degrees Fahrenheit. U.S. Patent# 9,551,142 Extra Large H.D.P.E. Interceptors Illustrated with direct connect lid (Option -DCL) Illustrated with standard lid system 6” A D1 D2 E1 C1 C2 E2 60 34 ”4” 4 1/2"Ø23 1 2 ” Inlet Optional vent connections on top internal bale Model Liquid Holding Capacity Grease Ret. with Flow Rate @ 100 GPM Grease Ret. with Flow Rate @ 250 GPM A Width B C¹ Dim. C² Dim. D¹ Dim. D² Dim. E¹ Dim. E² Dim. F Connection Size Shipping Weight (Lbs.) SUPER-500 500 U.S. Gallons 1,890 Litres 3,492 lbs.1,916 lbs.111" 2820mm 64" 1630mm 18.75" 476mm 37.25" 946mm 26.25" 667mm 24.25" 616mm 45" 1143mm 61.50" 1562mm 4" 102mm 950 SUPER-750 750 U.S. Gallons 2,840 litres 5,002 lbs. 2,875 lbs. 111" 2820mm 64" 1630mm 18.75" 476mm 37.25" 946mm 34.88" 886mm 32.88" 835mm 53.63" 1362mm 70.13" 1781mm 4" 102mm 1,015 SUPER-1000 1000 U.S. Gallons 3,790 litres 6,577 lbs. 3,833 lbs. 111" 2820mm 64" 1630mm 18.75"476mm 37.25"946mm 45.25"1149mm 43.25" 1099mm 64" 1626mm 61.50" 1562mm 4" 102mm 1,075 SUPER-1250 1250 U.S. Gallons 4,921 litres 8,177 lbs.4,983 lbs.111" 2820mm 64" 1630mm 18.75" 476mm 37.25" 946mm 56.25" 1429mm 54.25" 1378mm 75" 1905mm 91.50" 2324mm 4" 102mm 1,150 SUPER-1300 1300 U.S. Gallons 4,921 litres 8,501 lbs.4,983 lbs.111" 2820mm 64" 1630mm 18.75"476mm 37.25"946mm 56.25"1429mm 54.25" 1378mm 75" 1905mm 91.50"2324mm 4" 102mm 1,150 SUPER-1500 1500 U.S. Gallons 5,680 litres 9,862 lbs 5,750 lbs. 111" 2820mm 64" 1630mm 18.75" 476mm 37.25" 946mm 64" 1626mm 62" 1575mm 82.75" 2102mm 99.25" 2521mm 4" 102mm 1,250 SUPER-2000 2000 U.S. Gallons 7,570 litres 13,102 lbs. 6,600 lbs. 111" 2820mm 64" 1630mm 18.75" 476mm 37.25" 946mm 85.50" 2172mm 83.50" 2121mm 104.25" 2648mm 120" 3048mm 4" 102mm 1,350 Suix Optional Variations -AK Anchor kit (set of two) -C Lid extension (specify dimension required) -COA Coalescer Pack -DI Ductile iron lid & collar -DP Dosing pump -EP Enzyme port -FL-C Membrane clamp kit -F6 6” No Hub Inlet / Outlet connection (low rate of 700 GPM with 6" connections) -F8 8" No Hub Inlet / Outlet connection (fabricated stainless steel) (low rate of 1,200 GPM with 8" connections) -HLA High level alarm and loat switch (to be installed on site) -LHSI 4” no hub inlet on left hand side -LHSO 4” no hub outlet on left hand side -POK Remote pump out kit -RHSI 4” no hub inlet on right hand side -RHSO 4” no hub outlet on right hand side -RPO 4" Remote pump outlet connections on top of interceptor - specify location and number required -SB Sediment bucket -SP External Sampling port - inline, high connections (Part # BIG-SP) -SP-L External Sampling port - inline, low connections (Part # BIG-SP-L) -SP- OF External Sampling port - ofset (Part # BIG-SP-OF) -SST Fire resistant fabricated stainless steel interceptor -ST Fire resistant fabricated 10 gauge powder epoxy coated steel interceptor -V Vent connection - 4" (specify number required and location - side and / or top) -3 Stainless steel veneer bolted to top of ductile iron grates SUPER-1000 shown SUPER-500 ONLY with 100 GPM low rate GI1 Page: 11 / 20 EXTERIOR CLEANOUT ZZ1474P ZURN 4 NH HD CO W/ CI CVR ZZ14404NHBP ZURN 4" CO FERRULE W/BRONZE PLUG Page: 12 / 20 Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice SPECIFICATION SHEET TAG _______ * Regularly furnished unless otherwise specified. Zurn Industries, LLC | Specification Drainage Operation 1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax 814-454-7929 In Canada | Zurn Industries Limited 3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax 905-405-1292 www.zurn.com Rev. G Date:09/28/2017 C.N. No.138032 Prod. | Dwg. No.Z1474 ENGINEERING SPECIFICATION: ZURN Z1474 Heavy Duty Cleanout Housing. Dura-Coated cast iron body with integral anchor flange, secured scoriated cover with lifting device. The cleanout housing has an approximate weight of 38 lbs. [17 kg]. OPTIONS (Check/specify appropriate options) PREFIXES ____ Z Dura-Coated Cast Iron* ____ ZN D.C.C.I. with Polished Nickel Bronze Top (Add 3/16 [5] to 11 [280] Dim. & 3/4 [19] to 9 [229] Dim.) SUFFIXES ____ -DC Duresist Cover ____ -G Galvanized Cast Iron ____ -N With Internal Cleanout (See Z1440) (4, 6 [102, 152] Outlets Only) ____ -SG Solid Gasketed Cover ____ -VP Vandal-Proof Screw Z1474 HEAVY DUTY CLEANOUT HOUSING EXTERIOR CLEANOUT Page: 13 / 20 Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice SPECIFICATION SHEET TAG _______ * Regularly furnished unless otherwise specified. Zurn Industries, LLC | Specification Drainage Operation 1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax 814-454-7929 In Canada | Zurn Industries Limited 3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax 905-405-1292 www.zurn.com Rev. F Date:09/28/2017 C.N. No.138022 Prod. | Dwg. No.Z1440 Z1440 CLEANOUT FERRULE WITH PLUG Dimensions In Inches[mm]Approx. Wt. Lbs. [kg]A-Pipe Size E 2 [51]2-1/2 [64] 2 [1] 3 [76]2-3/4 [70] 4 [2] 4 [102] 3 [76] 5 [2] 6 [152] 3 [76] 8 [4] 8 [203]3-1/2 [89] 13 [6] OPTIONS (Check/specify appropriate options) PIPE SIZE (Specify size) OUTLET 'E' BODY HT. DIM. 2 ,3,4,6,8, [51,76,102,152,203]____ NH No-Hub See Chart PREFIXES ____ Z Dura-Coated Cast Iron Body and ABS Plug* SUFFIXES ____ -A Raised Head Plug ____ -BP Bronze Plug ____ -G Galvanized Cast Iron ENGINEERING SPECIFICATION: ZURN Z1440 Cleanout with Dura-Coated cast iron body, with gas and watertight ABS tapered thread plug. EXTERIOR CLEANOUT Page: 14 / 20 FCO ZZN14004NH ZURN 4 NH LVL TROL ADJ FLR CO W/ NB TOP Page: 15 / 20 Dimensional Data (inches and [ mm ]) are Subject to Manufacturing Tolerances and Change Without Notice SPECIFICATION SHEET TAG _______ ® * Regularly furnished unless otherwise specified. Zurn Industries, LLC | Specification Drainage Operation 1801 Pittsburgh Avenue, Erie, PA U.S.A. 16502 · Ph. 855-663-9876, Fax 814-454-7929 In Canada | Zurn Industries Limited 3544 Nashua Drive, Mississauga, Ontario L4V 1L2 · Ph. 905-405-8272, Fax 905-405-1292 www.zurn.com Z1400 EXTRA-HEAVY-DUTY "LEVEL-TROL" ADJUSTABLE FLOOR CLEANOUT PIPE SIZE (Specify size/type) OUTLET 'E' BODY HT. DIM. 2,3,4,6 [51,76,102,152]_____ IC Inside Caulk See Chart 2,3,4,6,8 [51,76,102,152,203]_____ NH No-Hub See Chart 2,3,4,6,8 [51,76,102,152,203]_____ NL Neo-Loc See Chart OPTIONS (Check/specify appropriate options) PREFIXES _____ Z Dura Coated Cast Iron* _____ ZB D.C.C.I. w/ Polished Bronze Light-Duty Top (Deduct 1/2 [13] from 'Y' Dim.) _____ ZN D.C.C.I. w/ Polished Nickel Bronze Light-Duty Top (Deduct 1/2 [13] from 'Y' Dim.) _____ ZS D.C.C.I. w/ Polished Stainless Steel Extra Heavy-Duty Top (Add 3/16 [5] to 'Y' Dim.) SUFFIXES _____ -AR Acid Resisting Epoxy Coated Finish _____ -BP Bronze Plug _____ -CF Carpet Flange Cover (ZB and ZN only) _____ -CM Carpet Marker _____ -DC Duresist Cover _____ -DX Round ZB or ZN Top with Dex-o-tex Flange (2, 3, 4 [51, 76, 102] Sizes only) _____ -G Galvanized Cast Iron _____ -HD Extra-Heavy-Duty Veneer Top (Add 1/8 [3] to 'Y' Dim.) (ZB and ZN only) _____ -K Anchor Flange _____ -KC Anchor Flange w/ Clamping Collar _____ -PC Protective Cover _____ -SG Solid Gasketed Cover _____ -SM Special Marking Stamped on Top _____ -T Square Top _____ -TC Neo-Loc Test Cap Gasket (2, 3, 4 [51, 76, 102] NL Bottom Outlet Only) _____ -TX Square Top Recessed for 1/8 [3] Tile (ZB and ZN only) _____ -VP Vandal-Proof Screws _____ -X Round Top Recessed for 1/8 [3] Tile (ZB or ZN only) _____ -Z Round Top Recessed for 1-1/4 [32] Terrazzo (ZB or ZN only) ENGINEERING SPECIFICATION: ZURN Z1400 "Level-Trol" Adjustable floor cleanout, Dura-Coated cast iron body with gas and watertight ABS tapered thread plug and round scoriated cast iron extra-heavy-duty secured top (Specify finish Z, ZB, ZN, ZS) adjustable to finished floor. 7 [3] 8 [203] Neo-Loc No-Hub Inside Caulk A-Pipe Size C E Approx. Wt. Lbs. [kg.] Dimension In Inches[mm] 6 [152] 4 [102] 3 [76] 2 [51] 8 [203] 6 [152] 4 [102] 3 [76] 2 [51] 6 [152] 4 [102] 3 [76] 2 [51]13.8 [6.3] 14 [6.4] 18.3 [8.3] 32.2 [14.6] 29.9 [13.6] 10.6 [4.8] 7.9 [3.6] 11.9 [5.4] 21.9 [9.9] 23.5 [10.7] 6-7/8 [175] 6-7/8 [175] 6-7/8 [175] 6-7/8 [175] 4-5/8 [117] 4-3/4 [121] 4-3/4 [121] 4-3/4 [121] 7-1/2 [191] 4-3/4 [121] 4-3/4 [121] 4-3/4 [121] 5-7/8 [149] 6-1/2 [165] 6-1/8 [156] 6-1/8 [156] 7-1/4 [184] 9-1/4 [235] 4-1/8 [105] 4-1/8 [105] 5-1/8 [130] 8-1/4 [210] 9-1/4 [235] 4-1/8 [105] 5-1/8 [130] 5-1/8 [130] 8-1/4 [210] 9-1/4 [235] 7.7 [3.5] 10.3 [4.7] 22.2 [10.1] Rev. T Date:09/28/2017 C.N. No.138018 Prod. | Dwg. No.Z1400 FCO Page: 16 / 20 MISC SS PIPE & PTRAP GSP16LP IMPORTED 4 SS S10 316L A312 WELD PIPE K22092409 KUSEL 22092409 4" PTRAP SCH10,316SS Page: 17 / 20 Home >Pipe & Tubing >Stainless Steel Pipe & Tubing >Stainless Steel Pipe >Schedule 10 Welded Stainless Steel Pipe DESCRIPTION Þ Material: stainless steel Þ Material Type: 316L Þ Schedule: 10 Þ ASTM Spec: ASTM A-312 Þ Import Þ Length: SRL SIZE SKU 10 in GSP16L10 14 in GSP16L14 16 in GSP16L16 Call for Pricing 18 in GSP16L18 20 in GSP16L20 Call for Pricing 1/2 in GSP16LD 3/4 in GSP16LF 1 in GSP16LG 1-1/4 in GSP16LH 1-1/2 in GSP16LJ 2 in GSP16LK 2-1/2 in GSP16LL 3 in GSP16LM 4 in GSP16LP 5 in GSP16LS 6 in GSP16LU 8 in GSP16LX 12 in GSP1S6L12 SPECIFICATIONS ASTM Specifications ASTM A-312 End Connection 2 Weld Origin Global Pipe Tubing Size 4 in Type Welded 4 in. Schedule 10 Welded Stainless Steel Pipe GSP16LP www.ferguson.com Page 1 of 24 in. Schedule 10 Welded Stainless Steel Pipe - GSP16LP|ISP16LP|GSP16LPN|1703034... 11/27/2019https://www.ferguson.com/product/4-in-schedule-10-welded-stainless-steel-pipe-gsp16lp/... MISC SS PIPE & PTRAP Page: 18 / 20 RESOURCES Kusel’s Stainless-Steel P-Trap performs best in situations where consistency of material, sanitation, and corrosion resistance are top priorities when connecting the drain outlet to the mainline. P-TRAP DETAILS Is full-weld stainless-steel Available with your choice of connections. 304 or 316L stainless-steel Schedule 40 or Schedule 10 Diameters from 1½” to 12” FIND A SALESPERSON CONTACT KUSEL SOCIAL SHARE Page 1 of 4Stainless Steel P-Traps | Kusel Stainless Products 11/27/2019https://www.kuselequipment.com/products/stainless-steel-drains/p-traps/stainless-steel-p-... MISC SS PIPE & PTRAP Page: 19 / 20 Page: 20 / 20